LAB NO: (2723)220-0095

CPSA – Consumer Product Safety Act

Teamhcmmx

FHSA – Federal Hazardous Substances Act
CPSIA – Consumer Product Safety Improvement Act
FFA – Flammable Fabrics Act

This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the d ate of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein.

The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us.

Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents.

CLASSIFICATION EXEMPT DUE TO FABRIC WEIGHT: PLAIN SURFACE WITH >2.6 OZ/SQ.YD. THE SUBMITTED SAMPLE(S) IS(ARE) EXEMPT FROM FLAMMABILITY TESTING IN ACCORDANCE WITH 16 CFR 1610.1(D) WHICH STATES: SPECIFICEXEMPTIONS EXPERIENCE GAINED FROM YEARS OF TESTING IN ACCORDANCE WITH THE STANDARD DEMONSTRATES THAT CERTAIN FABRICS CONSISTENTLY YIELD ACCEPTABLE RESULTS WHEN TESTED IN ACCORDANCE WITH THE STANDARD. THEREFORE, PERSONS AND FIRMS ISSUING AN INITIAL GUARANTY OF ANY OF THE FOLLOWING TYPES OF FABRICS, OR OF PRODUCTS MADE ENTIRELY FROM ONE OR MORE OF THESE FABRICS ARE EXEMPT FROM ANY REQUIREMENT FOR TESTING TO SUPPORT GUARANTIES OF THOSE FABRICS.

1. PLAIN SURFACE FABRICS, REGARDLESS OF FIBER CONTENT, WEIGHING 2.6 OUNCES PER SQUARE YARD OR MORE AND
2. 2. ALL FABRICS, BOTH PLAIN SURFACE AND RAISED-FIBER
   SURFACE, REGARDLESS OF WEIGHT, MADE ENTIRELY FROM ANY OF THE FOLLOWING FIBERS OR ENTIRELY FROM COMBINATION OF THE FOLLOWING FIBERS: ACRYLIC,MODACRYLIC,NYLON, OLEFIN, POLYESTER, WOOL.

CPSIA TOTAL LEAD CONTENT IN SUBSTRATES MATERIALS(CPSC-CH-E1001-
08.3 / CPSC-CH-E1002-08.3) TOTAL LEAD (Pb) (mg/kg) BLACK PLASTIC (DRAWSTRING END OF B):<10

USE & ABUSE (SMALL PART): TORQUE TEST & TENSION TEST (16 CFR 1500 51-53 / ASTM F963-17 section 8.8 - 8.9) (LBS.) A:
PATCH @ BODY: PARALLEL PULL & PERPENDICULAR PULL: #1-2: >15 LBS FOR 10 SEC B: DRAWSTRING @ WAIST: PARALLEL PULL: #1: >15 LBS FOR 10 SEC AGLET @ DRAWSTRING: PARALLEL PULL: #1-2: >15 LBS FOR 10 SEC LOOP @ WAIST: PARALLEL PULL: #1: >15 LBS FOR 10 SEC MIN. 15 LBS FOR 10 SEC. ((N/A)) / MIN. 4.0 IN-LBS.@ 10 SEC 180 DEGREES FROM ORIGINAL POSITION WHICHEVER COME FIRST B/C/E/F: N/A DUE TO NOT APPLICABLE ITEM

SMALL PART - CHOKING HAZARD(16 CFR 1501) A/B

MEET NO COMPONENT FITTING IN THE SMALL PART (TRUNCATED) CYLINDER ORIGINAL AND AFTER MECHANICAL HAZARDS.